Waterway Executive 4HP Impeller 48 56 Fr Pump Wet End Hot Tub Spa How To Video

Description

To See the How To Video about This Impeller go to YouTube and search for our videos.. "
Hot Tub Pump Wet End Seal How To Video American Spa Parts Seals
" or
"
Spa Hot Tub Waterway Executive Pump Seal Impeller & Bearing Replacement How To The Spa Guy
"
This is an
4HP
Impeller
for an Executive 48 Frame Wet End up to 4HP which would be Rare or a 56 Frame Wet End 4HP Motor. This Impeller would be on a motor that 12-14Amps on high speed which is very rare..This Impeller fits between the Face and the Volute of an Executive Wet End. I would advise replacing the Seal when you replace the Impeller. We offer a Seal, Silicone and Impeller individually or in a kit, and the Purpose of this Kit is to repair a Damaged Impeller and Seal inside the Wet End. This is (1) Impeller ONLY!!
NOTE: A 4HP
Impeller can be found on motors that are 12-14 Amps at 230V on high speed one way to determine is to look at the wear ring.. If the ring says
1,2 & 3
you choose a 3HP it if says
4 or 5
you choose a 4HP..
We
do offer FREE SHIPPING within the United States.
We Will Ship Worldwide using the Global Shipping Program only..
Visit our eBay Store as we also offer these and other associated products and accessories for your Spa.
ASP 310-4220
Note: A 115v motor that uses a 1 HP Impeller would show about 11-12.0 Amps on high speed a 230V motor would show about 8.0 Amps on High. See chart below for other Horsepowers.
Do Not choose a Larger Impeller thinking that it will make your Hot Tub Stronger it will only damage the Motor and make it run hot on high speed.
Note: There is usually a Horse Power Stamped into the center of the impeller for 2HP, 3HP and 4HP.. (See the picture example) 1HP and 5HP usually don’t have a stamp so you would determine those by the Amperage Chart..
To determine the HP refer to the chart below..
The difference between a 48 or 56 Frame wet end is the spacing of the Motor Thru bolts.
The 48 Frame will be 3 5/8" between or 5 3/16" in a X Pattern and the 56 Frame will be 4 1/8" Between or 5 3/4" in a X Pattern.
You must go by the Amperage Sticker on the motor not stickers on the Wet End or Motor especially the BHP Stickers.
Look on the label of the motor for the two amperages if you have a 2 speed pump or if its a single speed look for a single amperage. An example will look something like this:
10.0/3.5
The 10.0 is the high amperage in this example.
115V Chart Below
3/4HP 8-9 Amps
1HP 11-12 Amps
1.5HP 16-17 Amps
2HP 19-20 Amps. 2HP would be very rare
.
230V Chart Below
8.0 = 1 HP
10.0 = 2 HP
12.0 = 3 HP
14.0 = 4 HP
16.0 = 5 HP
NOTE: Your pump or motor may say a different Horse Power than what you see here,
DO NOT
go by what is listed on the motor, go by the amperage on the label.
NOTE for the NOTE: TRUST ME ON THIS, everybody lies about their Horse Power. But the amperage does not lie. Most people are told incorrectly that they have 5 HP pumps.
If you do the math two 230V 5 HP pumps at 16 amps is: 32 amps.
Plus a 5.5 KW heater is:
+ 21 amps.
That means with both pumps running and the heater on it will draw  =
53 AMPS
.
I bet your HOT TUB is on a 50 AMP breaker…... Therefore contrary to what you have been told you
DO NOT
have a 5 or 6 or 7 Hp pump.